TLG40 gantry mounting
TLG40 gantry mounting
Top lift spreader
Top lift spreader
|
Front page
|
Keeps you updated
|
Why Bromma is leading
|
Spreaders & options
|
What we can do
|
Articles and videos
|
Find your contact
|
Buy original spare parts
|
|
The Bromma TLG40 is a telescopic top lift spreader for the handling of single ISO and Binnen containers with masted lift trucks fitted with a gantry.
The industry must innovate to address container handling demand and this is just what Bromma did with the TLG40 - it is set to revolutionize the way drivers operate with the spreader increasing efficiency and productivity for a minimized total cost of ownership.
The spreader can adjust its length to lift containers from 20’ to 40’ using ISO floating twistlocks. Mechanical Pile Slope (MPS) or Powered Pile Slope (PPS) (optional), side shift, slew and reach features enable easy location onto containers achieved with smooth control technology. Additional tilt is achieved with the lift truck mast.
The TLG40 is attached to the gantry with 4 telescopic hangers for spreader self leveling with containers lying on trailers with pile slope up to 5°. Integrated gantry mounting increase capacity and decrease Loss of Load Centre (LLC). The telescopic spreader is of a monobeam frame construction designed to absorb both vertical and horizontal forces. Four ISO twistlocks engage the containers top apertures and lock into the corner castings.
The TLG40 is controlled with 24 VDC solenoid operated valves and inductive proximity sensors. The electrical system is designed to ensure maximum safety during operation. All motions of the spreader are controlled from the driver’s cab over serial communication (CANopen) or parallel wiring (optional) and all commands are processed safely by the spreader Electronic Control Unit (ECU). Lifting allowance is monitored by the ECU and implemented on the lift truck to ensure safe container handling. In addition, the onboard ECU offers self-diagnostic technology, derived from Bromma’s innovative SCS³ crane spreader control system.
Made of high quality steel and components, the TLG40 spreader achieves greater performances with lower tare weight, extended service intervals and longer likely replacement cycles. Available with several options, the Bromma TLG40 will enhance driver’s experience for a maximum productivity.
The spreader can adjust its length to lift containers from 20’ to 40’ using ISO floating twistlocks. Mechanical Pile Slope (MPS) or Powered Pile Slope (PPS) (optional), side shift, slew and reach features enable easy location onto containers achieved with smooth control technology. Additional tilt is achieved with the lift truck mast.
The TLG40 is attached to the gantry with 4 telescopic hangers for spreader self leveling with containers lying on trailers with pile slope up to 5°. Integrated gantry mounting increase capacity and decrease Loss of Load Centre (LLC). The telescopic spreader is of a monobeam frame construction designed to absorb both vertical and horizontal forces. Four ISO twistlocks engage the containers top apertures and lock into the corner castings.
The TLG40 is controlled with 24 VDC solenoid operated valves and inductive proximity sensors. The electrical system is designed to ensure maximum safety during operation. All motions of the spreader are controlled from the driver’s cab over serial communication (CANopen) or parallel wiring (optional) and all commands are processed safely by the spreader Electronic Control Unit (ECU). Lifting allowance is monitored by the ECU and implemented on the lift truck to ensure safe container handling. In addition, the onboard ECU offers self-diagnostic technology, derived from Bromma’s innovative SCS³ crane spreader control system.
Made of high quality steel and components, the TLG40 spreader achieves greater performances with lower tare weight, extended service intervals and longer likely replacement cycles. Available with several options, the Bromma TLG40 will enhance driver’s experience for a maximum productivity.
Major features:
- Low tare weight for high performances
- Increased capacity and decreased LLC
- Smooth control technology
- 20’ to 40’ at maximum speed with dampening
- Floating ISO twistlocks
- ±400mm hydraulic side shift
- ±5° slew / ±120 mm reach
- ±5° MPS
- Full CANopen bus integrated management
- Longer service intervals
- Light but robust thanks to well proven design for a long economic life
Technical specifications
TLG40 Top Lift Spreader, gantry mounting.
|
LIFTING CAPACITY (SWL) |
45 t up to ±10% eccentric loading 4 x 10 t with lifting lugs on twistlocks endbeams |
| TARE WEIGHT (TW) |
5,000 kg approximately, without extra equipment |
| ISO FLOATING TWISTLOCKS |
90° in less than 1,5 sec mechanical & electrical safety interlock system |
| SLEW |
±5° with smooth control technology |
| REACH | ±120 mm with smooth control technology |
| SIDE SHIFT |
±400 mm in less than 8 sec with smooth control technology |
| MECHANICAL PILE SLOPE | ±5° self leveling with 4 telescopic hangers |
| ELECTRICS | 24 VDC control voltage Electronic Control Unit with diagnostic technology Serial interface CANopen according to CiA DS 444 profile 2 working lights 70W each 3 indication lights unlocked (G) – landed (Y) – locked (R) |
| HYDRAULICS |
70-90 l/mn at 160 bar ISO cleanliness rating 18/16/13 (ISO 4406) |
| SURFACE CONDITIONING | PUR RAL 7021 (black grey) 120/2 FeSA2,5 with gloss grade 30±5 for a corrosion protection classification C3L/C2M according to EN - ISO 12944 |
An extensive list of options enables you to adapt the spreader more precisely to your needs. Further information is available on request. This specification is subject to alterations without prior notice.
